Alan
-
Gesamte Inhalte
29 -
Benutzer seit
-
Letzter Besuch
Inhaltstyp
Profile
Forum
Galerie
Beiträge erstellt von Alan
-
-
I think you can still get them for Victoria´s from cinemeccanica.BUT they are not cheap.
gruss
alan
-
if you are into electronic or know someone,then take the LT+RT from the back of the cp65,and sum them through a opamp,then you have left-center-right,and l+r still have the surr. info
alan
-
The CP55,had a 03 format,where the surround were turned off.BUT it was just turned off.The CAT150 still decoded it.A few film in the start of DOLBY STEREO did not have surround information.therefore format 03.
When the CP55 later was converted to have SR the buttom was changed to this.
You can still in the CP65 make this format,on the matrix card,but it wil do the same.Just turn off the surroundchannel.
alan
-
Hi
PM me,I have something.
alan.lyman(at)mail.dk
gruss
alan
-
vor 13 Minuten schrieb holgertomas:
Hallo Zusammen,
ich wollte eine alte Telleranlage in Betrieb nehmen, aber anscheinend wurde da Mal dran herumgebastelt. Es ist der Teller aus den 70ern mit den Drehschaltern.:
Im Stillstand sind alle Funktionen okay. Bekommt aber der Teller vom Projektor zum Start die Phase auf Klemme EX 61, beginnt zwar der Teller, der auf Abwickeln geschaltet ist, zu laufen, aber alle Kontrolllampen über den Drehschaltern schalten ab und die Relais, die von der Steuereinheit am Teller gesteuert werden, reagieren nicht mehr. Also läuft der Teller mit einer konstanten Geschwindigkeit und wird weder gebremst noch beschleunigt.
Kann Jemand helfen oder hat vielleicht das Manual auf deutsch?
Beste Grüße
Holgeryou have to activate the takeup arm,before you can control the speed on the takeout disc with the unit.
Alan
-
there has been MANY different electric setups,inside a V5.you must start to oplaod a picture from inside.then maybe I can help
alan
-
-
-
-
I think I have the breakoutboards for this.Also I made my own,when connected to a DA20,because the DA20,will revert the CP65,when not running SRD.If you are interested
alan
-
I might have some,shall I look??
gruss
Alan Danmark
-
Hello Karel
There are several different motor for this projector,both 3phase and single fase.
do you have the toothed wheel for the motor?If yes count how many teeth
if you email me,I can send you the manual
alan
-
Hello jerry
normally there are only two parameters you are alowedd to adjust.
the angle and how much in that angle.
alan
-
good to know
alan
-
It could be when you shut it off,Its not uncommon to have card faults in the log,when shutting the cp off,because it sees it as a fault,when its just shutting down.
alan
-
Maybe its because you send a "mute"command first.try to delete that.
alan
-
hello
you shoulld try to replace all the microswitches on the side.they are standard,and I have replaced many,because of many different faults.Maybe first check that it is aligned perfectly,so all switches is engaed when they should.I might have a pdf schematic of it.
alan
-
I think at the end,they used IDE and with a scsi adpatorplate at the back
-
youre welcome.
good luck
gruss
alan
-
I have repaird alot of these
you open them,by banging a screwdriver along the line,allaround,then it opens.
the problme is usually,that you have to resolder the plug.Also I used to glue the plug to the PCB.
Sometimes it´s the trimmer which is bad,and I replace it.
after repair,I just glue the two pieces together again.
gruss
Alan
-
great.
have fun
alan
-
Hello
If you only use 1projector,make sure the short is made on the back on the "motorrelay"plug,for M1
otherwis it will not revert when no SRD
alan
-
Hello
you must be sure that it is a short version 2000w bulb,with same size as a 1600w.ALSO very important,the mirror has to be the cold mirror,and there shall be the anode cooler mounted.
If the lamphouse was ordered for 1000w,then this might not be mounted.Also the bulbadaptor is longer for 1000w bulbs,than the 1600/2000w bulb.
gruss
Alan
Danemark
Dolby Cat 763 - Netzteil CP 650
in Technik
Geschrieben
You can change the capacitors in the powersupply.I have done that on several with same problem.its a bit tricky,so you must be an electronic guy to do it,not to destroy the PCB.they sit very tight,so you have to find the same sizes.
gruss
alan Danemark