Installing the hard-disk drives You must install each HDD into the Dolby IMS3000. Note: Each HDD must be from the Dolby approved HDD list. Dolby prohibits intermixing SATA I HDDs with SATA II HDDs. Procedure 1. Remove the Dolby IMS3000 from its carton and antistatic bag. 2. Release the lever of the HDD carrier by pressing the release tab, and insert the HDD into the HDD slot with the handle open. The three HDD slots are labeled as HDD-1, HDD-2, and HDD-3 on the Dolby IMS3000 front panel. 3. Push the HDD handle into the Dolby IMS3000 HDD slot until it locks into place. 4. Repeat this procedure for the remaining HDDs. 3.2 Preparing to install the Dolby IMS3000 into a projector After each HDD is installed, you must insert the Dolby IMS3000 into a projector and then continue the hardware installation and configuration. You can insert the Dolby IMS3000 into an NEC, Barco, or Christie Series 2 projector.
Connecting the Dolby IMS3000 to an automation controller You have the option to connect the Dolby IMS3000 to an automation controller using two shielded CAT5 or CAT6 RJ-45 cables. Basically I have to do the same while developing an app with the help of iphone app development agency. Procedure 1. Connect one end of a shielded CAT5 or CAT6 cable to the general-purpose input (GPI) port, labeled GPI, on the Dolby IMS3000. 2. Connect the other end of the shielded CAT5 or CAT6 cable to whichever automation controller is available or required. 3. Connect another shielded CAT5 or CAT6 cable to the general-purpose output (GPO) port, labeled GPO, on the Dolby IMS3000. 4. Connect the other end of the shielded CAT5 or CAT6 cable to the automation controller.
Accepting the Dolby IMS3000 license agreement You must accept the license agreement in the Dolby IMS3000 web UI. Procedure 1. After you log in to the Dolby IMS3000 web UI, scroll to Setup & Maintenance > System Settings > License Agreement. 2. Scroll down this page, read the license agreement, and then select I have read and accept the terms of the software license agreement.
Inserting the Dolby IMS3000 into the NEC Series 2 projector Insert the Dolby IMS3000 into the NEC Series 2 projector. Note: Make sure to look for any obstructions. Do not force the Dolby IMS3000 into the projector, as this may cause damage to the connectors. Prerequisites Make sure that the NEC Series 2 projector is powered down and in the off position, and the power cord is disconnected from the wall. Follow standard electrostatic discharge procedures to protect the electronic components from damage. Procedure 1. Remove the NEC Series 2 projector filter cover.
Powering on the NEC Series 2 projector -
Procedure 1. Connect the power cable to the projector. 2. Turn the projector on. 5.3 Setting up the network for the Dolby IMS3000 and NEC Series 2 projector You must connect the Dolby IMS3000 to an NEC Series 2 projector and then to a laptop and a local network switch. Use ETH-0 to begin the installation process. All Dolby IMS3000 units are shipped from the factory with this default IP address for ETH-0: • IP: 192.168.100.50 • SM: 255.255.255.0 • GW: Blank Ethernet ports ETH-1 and ETH-2 are set to Dynamic Host Configuration Protocol (DHCP) by default and should not be used for initial configuration. Prerequisites You need three Ethernet cables for this task. Procedure 1. Take the first Ethernet cable, and connect it to the Dolby IMS3000 Ethernet port labeled ETH-0. Next, connect the other end of this Ethernet cable to the local network switch. 2. Take the second Ethernet cable, and connect it from the NEC Series 2 projector to the same local network switch as step 1. 3. Take the third Ethernet cable, and connect it from the local network switch to a laptop. 4. To set up the network configuration on the laptop to connect to the Dolby IMS3000: a. Open the laptop network settings, and then open the IP address settings dialog. b. Select Internet protocol version 4 (TCP/IPv4) from the available options. c. Set the IP address to 192.168.100.25 and the netmask to 255.255.255.0
d. Set the network to the desired network connection. 5. To log in to the Dolby IMS3000 web UI, use a web browser and enter the default ETH0 port IP address, and then scroll to Setup & Maintenance > System Settings > Networking Configuration. 6. Select and configure ETH-0, ETH-1, or ETH-2 as needed for installation. If you change the settings for ETH-0, you need to change the computer settings to access the Dolby IMS3000 again
Adding the NEC Series 2 projector as a device You must add and then configure an NEC Series 2 projector as a new device in the Dolby IMS3000 Device Manager. Procedure 1. Open a web browser and enter the Dolby IMS3000 IP address. 2. Enter the log-in credentials, and then click Login
Hope this will help everyone.
